Ankersmid M&C
About us
Ankersmid M&C is a company that specializes in providing analysis solutions for gases, liquids and solids. Our company has been a distributor of internationally renowned brands of analysis equipment for various applications for decades.
Our partners include:
Gas: Ankersmid Sampling, Neo Monitors, Protea, Eco Physics, Testa, Fuji Electric, Envea GmbH (Mercury Instruments),, Anseros, Dr. Födisch, Oizom, Kemtrak,...
Water/liquids: Horiba Tocadero, Strathkelvin Instruments, Thermo Scientific, Anseros, Envea GmbH (Mercury Instruments), Kemtrak, Liquids Solids Control, Marimex, Sensmet,...
Solids: Liebherr, Marimex,...
Products & services
NEO LaserGas II SP Monitor
Single Path monitors from Neo Monitors are designed for in-situ measurement in chimneys, pipes or reactors with typical path lengths from 0.5 to 20 meters. By-pass and extractive configurations are also possible. The compact design consists of the transmitter (with laser module, optical module and main electronics) and receiver (with focus lens, photo detector and receiver electronics). The LaserGas II SP Monitor uses a transmitter/receiver configuration (mounted diametrically opposite) to determine the average gas concentration over the optical path length.
Neo LaserGas II SP Compact Monitor
The Neo LaserGas II SP Compact Monitor is derived from the standard Single Path instruments and has been optimized for applications with short path lengths between 10 and 100 centimeters. Because the device is equipped with a focused laser beam, it is possible to measure through very thin insertion tubes (<10 mm diameter). As a result, only a very limited flushing rate is required with the SP Compact for applications where rinsing of the lens to prevent dust deposits is necessary. With the optional internal desiccants, these devices can also be optimized for in-situ measurement of trace levels of eg O2 and H2O. The LaserGasTMII SP Compact Monitor consists of a transmitter/receiver (mounted diametrically opposite each other) to determine the average concentration of gas along the optical measurement field.
Neo LaserGas III Monitor
The Neo LaserGas III Single Path Monitor for Oxygen is designed for use in hazardous areas. The device is based on the third generation LaserGas electronics and was provided with a compact flameproof housing and can therefore be used in ATEX zone 1 and class l division 1 . The LaserGas III SP is our most reliable gas sensor with all electronics designed to IEC 61508 and SIL 2 (Safety Integrity Level). The LaserGas III SP O2 consists of a transmitter and receiver (mounted diametrically opposite each other) and measures the average O2 concentration over the optical path length. Typical path lengths are 0.5 to 20 meters.
Analyseur multicomposants NEO LaserGas™ iQ2 pour O2, CO, CH4, H2O et température
LaserGas™ iQ² analyzer is the first to measure up to four gases (O2, CO, CH4, H2O) and temperature depending on configuration, which eliminates the need for multiple units for combustion analysis. The cutting-edge design and ground-breaking functionality, ensures that the instrument delivers unmatched reliability and durability. Customers may replace existing analyzers where explosion risks or high maintenance issues are a huge concern.
Marimex's Viscoscope on-line viscometers
Marimex's Viscoscope on-line viscometers ensure proper operation in any industry sector. The modular process viscometers consist of a sensor and transmitter and are manufactured for use in both standard and very customer specific applications. The Marimex portfolio includes sensors for low to high measuring ranges (0.1-2.500.000 mPa.s), process temperatures up to 450°C, process pressures up to 450 bar and ATEX applications. Furthermore, the measuring system is completed with pipe adapters, flow cells, diving sensors, etc.. Marimex offers 2 series of viscometers: •VA-100: measuring range up to 25,000 mPa.s, T up to 130°C, P up to 64 bar, non-Atex •VA-300: measuring range up to 2,500,000 mPa.s, T up to 450°C, P up to 450 bar, option Atex
Online Moisture measurement system Litronic FMS II
A self-sufficient system with almost unlimited possibilities. The Litronic FMS II type moisture measuring installation has been used for decades in a wide range of industries to measure the moisture content of various materials in real time.At the beginning of each measurement section, the calibration per product must be carried out by means of reference procedures. The Litronic-FMS II software enables convenient and fast parameterisation. The evaluation unit receives the raw values measured by the Liebherr sensors and immediately converts them into percentage humidity. Thanks to the various interfaces, transfer to a higher-level control is possible. Measurement by the Liebherr sensor system is based on the physical principle of capacitance determination in the high-frequency stray field. In addition to their high precision and robustness, the measuring devices from Bad Schussenried are characterised by their reproducibility. Once the system has been calibrated, further measuring points can be set up or devices renewed on this basis at any time without great effort. The plant thus always remains reliable, regardless of its previous term and age.
Water online sodiumanalyzer
Protect your turbine against destructive sodium levels, including trace amounts, with the reliable and easy to use Thermo Scientific™ Orion™ 2111LL Low Level Sodium Analyzer. Available in several configurations including the analyzer instrument only, or with a protective enclosure.
Water online chlorine analyzer
Detect chloride in real time with accurate and reliable results using the Thermo Scientific™ Orion™ 2117XP Chloride Analyzer. Early detection of chloride ingress from feedwater helps your plant maintain the optimal balance of water purification and peace of mind.
Online Silica analyzer
Avoid productivity lapses by ensuring your silica analyzer is always ready to go. Our maintenance and consumables for the Thermo Scientific™ Orion™ 2230XP silica analyzer include caps, maintenance kits and replacement parts.
Eco Physics nCLD series NOx Analyzers
The new generation of NOx analyzers from Eco Physics with a compact and modular construction guarantees the best performance with the highest possible reliability!
Testa iFiD Rack
19" RackFlame-Ionisation-Detector iFiD Rack for continuous monitoring The stationary Flame-Ionisation-Detector (FID) iFiD RACK is designed for stack monitoring, process control and also for VOC measurement. The whole gaspath is heated to 300°C and so we can speak from a Hightemperature-FID. Features: - User-friendly Touchpanel 7” TFT - Single Range – no switch between ranges - Graphic Display of HC-concentration - Heated integrated Samplegasfilter 300°C - Internal Datalogging by USB Stick - Built in Zero Gas generator (option) - Internal response factor correction - Pyrolysis cleaning function for a self-cleaning procedure of the gas path and cell
Kemtrak DCP007-UV Photometer
The Kemtrak DCP007 UV process analyzer uses ultra-low power cold light at the exact wavelength required for the analysis, exposing the sample to thousands of times less energy than a traditional UV photometer. This is achieved from a state of the art digital photometer design using a modulated high performance UV LED light source with precision fiber optics. Industrial fiber optic measurement cells for chemical concentration, platinum cobalt, hazen, saybolt, ASTM, chlorine dioxide and ICUMSA color.
Sensmet µDOES® Multi-metal Water Analyser
Sensmet's breakthrough technology, Micro-discharge Optical Emission Spectroscopy µDOES®, allows for multi-metal analysis of industrial and environmental water samples. Ultra-pure water, brines and process water are Sensmet’s target applications. Sensmet µDOES® Multi-metal Water Analyser can measure up to 30 metals in water, at part-per-billion (ppb) sensitivity: • Lithium (Li) • Titanium (Ti) • Silver (Ag) • Sodium (Na) • Vanadium (V) • Gold (Au) • Potassium (K) • Chromium (Cr) • Mercury (Hg) • Magnesium (Mg) • Manganese (Mn) • Cadmium (Cd) • Calcium (Ca) • Iron (Fe) • Aluminum (Al) • Strontium (Sr) • Barium (Ba) • Scandium (Sc) • Yttrium (Y) • Thulium (Tm) • Cobalt (Co) • Nickel (Ni) • Copper (Cu) • Zinc (Zn) • Ytterbium (Yb) • Gallium (Ga) • Indium (In) • Lead (Pb) • Erbium (Er)
Ankersmid Portable Gas Sample Probe APP
Due to various acid dew points at various applications the probe is heated up to 180°C. A filter element of 150mm is integrated, suitable for most applications up to 1g dust/m3. A significant advantage is that this filter is replaceable without dismounting the probe. With the filter element of 150mm length this probe is suitable for most applications up to 1g dust/m3; with the blow-back function dust loads of up to 10g/m3 can be handled.
Strathkelvin ASP-CON: Activated Sludge plant controller
ASP-CON can be installed permanently into several different areas in the Secondary Wastewater Treatment Plant to provide feed-forward or feed-back control for plant operation and optimisation. The ASP-Con carries out several continuous measurements, and also analyses discrete batch samples of the product to give the following parameters on a frequency which the plant operator can set: MEASUREMENT & BENEFITS DO Temperature Ammonium Potassium* pH* ORP* MLSS SVI/SSVI TSS (predicted) RAS Concentration Nitrification Levels* Oxygen Uptake Rate Specific Oxygen Uptake Rate Critical Oxygen Concentration Points Toxicity Management The ASP-CON achieves these measurements by a combination of mechanical and analytical methods that forms the basis of controlling the secondary treatment process. This also removes the need for manually completed tests, releasing time for other priority tasks. The ASP-Con instrument uses an innovative system for cleaning and calibrating that extends the service interval time and the design of the sample capture process, which negates problems associated with ragging that afflicts some wastewater treatment plants. The outcome of an ASP-Con controlled plant will be to achieve compliance for the optimum costs in energy and the reduction of significant CO2 emissions, and liberating labour for other priority tasks. There are 3 electrode options – Ammonium and a choice of the following:- Potassium or Nitrate pH or ORP
Protea P2000 in-situ gasanalysator
In-situ Continuous Emissions Monitoring (CEM) analysers are flange mounted to the emissions point, with an in-situ sample cell inserted into the stack. Installing an in-stack CEM analyser removes the need for costly and high-maintenance sample handling components. Protea offers both Infra-Red (IR) and Ultra Violet (UV) in-situ gas analysers. The in-situ CEM systems are multi-component and can monitor multiple gases species simultaneously. The analyser also monitors water vapour and so the pollutant gases can be reported on a wet or dry bases depending on the local environmental agencies requirements. The Protea In-Situ Analyser incorporates an automatic zero and calibration gas unit and is controlled by the microprocessor in the analyser. This allows the periodic zero and calibration to be carried out, fully challenging the system. In-Situ Gas Analysers The stack mounted analysers can accept up to five analogue inputs from third party instruments such as Oxygen, Velocity and Particulate. This gives the system the capability to report pollutant concentrations normalised and in mass units such as kg/hr. The stack mounted analyser is connected via a serial link to the analyser control unit, which displays, data logs and re-transmits the concentrations (ppm, mg/Nm3, %) of the monitored flue gas components. Up to eight (8) analysers can be connected to a single Protea Analyser Control Unit. Certification with environmental monitoring equipment standards is dependent on analyser series and application. Certification of models includes EN 15267-3 MCERTS; EN 14181 QAL 1 and US EPA 40cfr part 60 & 75.
Kemtrak TC007 Industrial Turbidimeter
The Kemtrak TC007 is an easy to operate industrial process fiber optic turbidimeter designed to accurately measure the concentration of light scattering components. Measurements are real time and in-line. Long life solid state LED lamps and precision fiber optics are used to provide drift and noise free measurement at very high precision. The Kemtrak TC007 can be configured to use the nephelometric method of turbidity measurement in accordance with International Standard ISO7027. In this mode, a proprietary algorithm mathematically combines the ratio of attenuated and scattered light to accurately monitor the turbidity of the sample. Automatic compensation of sample color and fouling of the optical windows ensures trouble free operation. Maintenance free measurement cells with scratch resistant sapphire windows have no electronics or moving parts making the unit suitable for hazardous area use. Benefits: - Real time in-line turbidity measurement - ISO 7027 compliant - 0.01 – 1 000 NTU/FTU - Zero maintenance - Reliable and robust infrared LED lamp - Extensive range of robust fiber optic measurement cells - Analogue output (0/4-20 mA) - Modbus (slave) over TCP/IP & Profibus (optional) - Local & web based graphical user interface (TCP/IP) - ATEX Exd IIB + H2 T6 IP66 Category II 2 G (optional)
Kemtrak DCP007-VIS Industrial Photometer
The Kemtrak DCP007 is an easy to operate industrial fiber optic photometer designed to accurately measure the concentration and color of process samples. Measurements are real time and in-line. The Kemtrak DCP007 uses a long life high performance LED light source with robust industrial grade fiber optics to provide drift and noise-free measurement with very high precision. A proprietary dual wavelength four channel measurement technique and advanced digital electronics design allows deep absorbance measurement to 5 AU. A range of shorter optical pathlengths allow for deeper absorbance measurements. Automatic compensation for sample turbidity and/or fouling of the optical windows ensures trouble free operation. Maintenance free measurement cells with sapphire windows have no electronics or moving parts making the unit suitable for hazardous area use. BENEFITS: - Real time in-line measurement - Drift and noise-free measurement - Down to 5 AU (1 cm OPL), deeper absorbance measurements with shorter pathlengths - Zero maintenance measurement cells & fiber optics - Long life LED light source that is easy to change - Analogue output (0/4-20 mA) - Modbus (slave) over TCP/IP & Profibus (optional) - Local & web based graphical user interface (TCP/IP) - ATEX Exd IIB + H2 T6 IP66 Category II 2 G (optional)
Kemtrak DCP007-NIR Industrial Photometer
The Kemtrak DCP007-NIR is an advanced dual wavelength NIR photometer designed to accurately measure the concentration of process liquids and gasses with near-infrared (NIR) absorbance between 850 and 2000 nm. Examples of NIR measurements include moisture (water & trace water), ethanol, methanol, sodium hydroxide, ammonia and continuous fuel identification. The Kemtrak DCP007-NIR uses a long life high performance NIR LED light source with robust industrial grade fiber optics to deliver a drift and noise-free measurement with very high precision. Automatic compensation for sample turbidity and/or fouling of the optical windows ensures trouble free operation. BENEFITS: - Real time in-line measurement - 850 – 2000 nm dual-wavelength detection -Drift and noise-free measurement - Up to 5 AU (1 cm OPL), deeper absorbance measurements with shorter pathlengths - Temperature compensation - Zero maintenance measurement cells & fiber optics – no electricity or heat near the sample - Long life NIR LED light source that is easy to change - Analogue output (0/4-20 mA) - Modbus (slave) over TCP/IP & Profibus (optional) - Local & web based graphical user interface (TCP/IP) - ATEX Exd IIB + H2 T6 IP66 Category II 2 G (optional)
Kemtrak FL007 Industrial Fluorescence and turbiditimeter for the measurement of oil in water
The Kemtrak FL007 is a fiber optic probe based oil in water monitor. A state-of-the-art combined fluorescence and turbidity measurement assures reliable continuous monitoring of oil and hydrocarbon contamination in water. Mineral oils rich in aromatic content will fluoresce when illuminated with ultraviolet light. The intensity of this fluorescence is dependent upon the polyaromatic hydrocarbon (PAH) content of the oil. Typical oils that fluoresce include fuel oil, crude oil, hydraulic oil and transformer oil. Each oil has its own unique fluorescence intensity resulting from its specific PAH content. The combined fluorescence from both dissolved and dispersed oil in water can be measured and correlated to the oil content. Entrained gas and solids present in the stream will not fluoresce and therefore do not affect the measurement. However, non-mineral oils or hydrocarbons low in aromatic content may not fluoresce. Hydrocarbons and oils with a low water solubility will result in a turbid solution that can easily be detected using the dual turbidity measurement instantly informing the operator of leaks or contamination resulting in a high measurement confidence. The immersion probe has the same dimensions as industry standard Ø12 mm PG 13.5 pH sensors allowing a range of standard fittings and retractable probe holders to be used. BENEFITS: - Simultaneous UV fluorescence and turbidity - Hygenic Ø12 mm PG 13.5 immersion probe - Real time in-line measurement - Calibration for 16 different oil types - Suitable for hazardous area use - Alarm, 4-20mA and Modbus communications - ATEX Exd IIB + H2 T6 IP66 Category II 2 G (optional)
KEMTRAK NBP007 NIR Backscatter Photometer
The Kemtrak NBP007 is a high resolution backscatter photometer that revolutionizes the measurement of high concentration suspended solids. Traditional turbidity based optical measurement instruments lack resolution and stop working at approximately 1% suspended solids due to the extremely high optical density. This limitation is overcome with the NBP007 and for the first time the operator can monitor and have complete control over their process at any concentration. By knowing exactly what is happening at all times, process changes can be quickly implemented that result in substantial cost savings. BENEFITS: - 0.0005% (5NTU) … 80% suspended solids - Zero maintenance - Proprietary NIR Measurement technique - Display in NTU, FTU, ppm, mg/l, g/l or % - Robust hygienic TriClamp probe or Ø12mm PG13.5 immersion probe -designed for CIP processes - Analogue output (0/4-20 mA) - Modbus (slave) over TCP/IP & Profibus (optional) - Local & web based graphical user interface (TCP/IP) - ATEX Exd IIB + H2 T6 IP66 Category II 2 G (optional)
Testa iFiD Mobile
Portable Flame-Ionisation-Detector The Flame-Ionisation-Detector (FID) measures the Total Hydrocarbon concentration in industrial and laboratory environment. Because of it’s lightweight and compact dimensions, it is especially made for daily changing measuring points or short-time measurements. FEATURES: - User-friendly Touchpanel 7” TFT - Graphic Display of HC-concentration - Single Range – no switch between ranges - Heated integrated Samplegasfilter 300°C - Internal Datalogging by USB Stick - Built in Zero gas generator (option) - Internal Response factor correction
Ankersmid Gas Sample Probe Series ASP
Due to its modular design and various options, the Ankersmid heated sample probe filters cover the widest range of applications. With a choice of different lengths of heated filter body, a filter element of 150mm length, suitable for most applications up to 1g dust/m3 can be integrated. 180mm filters with a larger filter surface are used for applications up to 4g dust/m3; with the blow- back function dust loads of up to 10g/m3 can be handled.
Ankersmid Compressor Cooler ACC 4xx
The ACC cooler offers precision, safety and long-term stability for extractive analytics. The very low gas dissolution rate is attained owing to the new cooler technology (Patents applied). Both the permanent separation of the condensate from the gas phase, as well as the shorter contact time of the gas in the system, plays important roles in reducing gas dissolution rates. The new cooler incorporates an advanced structural design with housing suitable for both wall-mounting and 19“-racks. The coolers can be integrated into the analysis cabinet without empty space requirements at the side for a cooling air outlet. The new design enables up to 4 heat exchangers and peristaltic pumps to be incorporated either at the factory or at a later time, without any problem. The exchangers and pumps can be connected in series or parallel following customer requirements. An electronic system not only monitors the dew point, but also the ambient temperature. The integrated fan is cooling air temperature dependent controlled. A temperature alarm output is wired to the terminal block incorporated of the cooler housing for a safe connection without disassembling the cooler. Available for 230VAC and 115VAC power supply. The ACC cooler is designed especially for: – Power Plants – Waste Incinerators – Cement Manufacturing – Chemical Production Plants – Gas Production Plants – Glass manufacturing – Timber Processing – Food Processing
Ankersmid Mini Compressor Cooler ACC 1xx/2xx Series
The ACC cooler offers precision, safety and long-term stability for extractive analytics. The very low gas dissolution rate is attained owing to the new cooler technology (Patents applied). Both the permanent separation of the condensate from the gas phase, as well as the shorter contact time of the gas in the system, plays important roles in reducing gas dissolution rates. The new cooler incorporates an advanced structural design with housing suitable for both wall-mounting (standard) and 19“-racks by using optional brackets. The coolers can be integrated into the analysis cabinet without empty space requirements at the side for a cooling air outlet. The design enables 1 or 2 heat exchangers to be incorporated either at the factory or at a later time, without any problem. The exchangers can be connected in series or parallel following customer requirements. An electronic system monitors the dew point and controls the integrated fan. A temperature alarm output is wired to the terminal block incorporated of the cooler housing for a safe connection without disassembling the cooler. Available for 230VAC and 115VAC power supply.
Ankersmid Peltier Cooler APC 14XX-16XX Series
This unique microprocessor controlled Peltier Cooler has been designed with a powerful dew point stabiliser. The dew point is set at 4°C but can be changed at any value between 1 and 15°C. The condensate that is formed should be removed by a peristaltic pump, automatic drain or collection vessel. The heat exchanger is demountable and PFA®-coated.
On-Line TOC Analyzer - TOCADERO One
On-line water analytics with HORI BATOCADERO The TOCADERO ONE analyzer takes the evolution of modern online water analytics to the next level. The analyzer platform combines sophisticated water analytics, stringent requirements in terms of accuracy and reliability, and the latest sustainable and future-proof hardware and software solutions. Based on the unique platform architecture of the TOCADERO ONE, the range of available analytical parameters is being continuously expanded. TOC & TNb analysis. The sum parameters TOC and TNb are some of the most important parameters in water and wastewater analysis. While the TOC (total organic carbon) provides information about the organic substance pollution in water, the TNb (total nitrogen bound) reflects the nitrogen pollution. The TOC is determined in accordance with DIN EN 1484 and the TNb in accordance with DIN EN 1 2260. The thermal oxidation at 1,200°C is particularly beneficial for determining both sum parameters. Water analysis of the next generation Highest analytical precision with short measuring time Catalyst-free high-temperature process at 1 200°C with "Fast Change Technology Most modern hardware components and industry 4.0 features Minimal material requirements and support costs Highest processing quality "Made in Germany" Global service and support Convincing cost of ownership
Polludrone Smart
The Polludrone Smart is an air quality monitoring device specially developed to monitor ambient air quality. The Polludrone Smart is a compact and connected CAAQMS which offers near real-time air quality data of all the National Air Quality Index (NAQI) parameters. The ease of installation and the requirement for minimal space for deployment makes it a scalable solution to be deployed at multiple locations. For instance, deploying the Smart version creates an air quality sensor network for crucial applications like Smart Cities, Roadside monitoring, Occupational Health monitoring. Polludrone Smart measures all the AQI parameters such as PM2.5, PM10, Carbon Monoxide (CO), Carbon Dioxide (CO2), Sulfur Dioxide (SO2), Nitrogen Dioxide (NO2), Ozone (O3), Ambient Noise, Light, UV, Temperature, and Humidity. Therefore, by deploying Polludrone Smart we focus on AQI monitoring. The Polludrone Smart is technologically equipped to offer higher accuracy with features like patented e-breathing technology, humidity correction for Particulate monitoring, Auto device firmware updates, Anti-static inlet to avoid loss of particulate during sampling, and remote calibration capabilities. Additionally, our Intelligent Air Quality Monitoring device can transmit data through various data communication modules like GSM, WiFi, LORA, etc. Hence, the device transmits data to the Oizom cloud in near real-time. Also, it has an inbuilt memory backup to ensure no data loss in case of network failure. The collected data can be visualized on the Oizom IoT Terminal in the form of real-time dashboards, automated reports, and smart alerts. Moreover, the data accessibility through Rest APIs for integration into 3rd party software and Central Command Centre is also possible.
Dustroid Smart
The Dustroid Smart is an air particulate monitoring device specially developed to monitor ambient dust particles. The Dustroid Smart is a compact and connected optical particle counter which offers near real-time particulate matter count. The easy to install and the requirement for minimal space for deployment make it a scalable solution to create a dense network of data points. The Smart version is specially designed for creating a quality sensor network for crucial applications like Smart Cities, Roadside monitoring, Tunnel monitoring. Dustroid Smart – dust monitoring device measures all the PM parameters like PM1, PM2.5, PM10, PM100, Temperature, and Humidity. The Dustroid Smart is technologically equipped to offer higher accuracy with features, humidity correction for Particulate monitoring, Auto device firmware updates, Anti-static inlet to avoid loss of particulate during sampling, and remote calibration capabilities Our intelligent optical particle counter can transmit data through various data communication modules such as GSM, WiFi, LORA, etc. The data is transmitted to the Oizom cloud in near real-time. Additionally, it has an inbuilt memory backup to ensure no data loss in case of network failure. The collected data can be visualized on the Oizom IoT Terminal in the form of real-time dashboards, automated reports, and smart alerts. The data can also be accessible through Rest APIs for integration into 3rd party software and automated dust suppression.
Odosense Smart
The Odosense Smart is a smart odour monitoring device specially developed to monitor odorants in the ambient atmosphere. The Odosense smart is a sensor-based IoT powered online odour monitor for peripheral monitoring across odourful sites and activities. So, the smart odour monitor is used for applications like monitoring in and around facilities like solid waste monitoring plants. Odour monitoring around solid waste plants, dump yards and landfills is very crucial as they are usually around the city vicinity and the odour nuisance could be a health hazard for the surrounding residents. It is also essential to keep a track of odour intensity to take suggestive actions like planning odour mitigation activities. Additionally, in the case of false complaints, the authorities have the data for reference purposes. Odosense Smart measures odourful parameters such as Sulfur Dioxide (SO2), Hydrogen sulphide (H2S), Ammonia (NH3), Methyl Mercaptan (CH3SH), TVOC (Benzene, Toluene, Xylene), Temperature and Humidity. The Odosense Smart is technologically equipped to offer higher accuracy with features such as patented e-breathing technology, Auto device firmware updates, and remote calibration capabilities. Additionally, our systems are backed with AI ML algorithms to understand odour levels and impact. Odosense Smart Odour Monitoring Device can transmit data through various data communication modules such as GSM, WiFi, LORA, etc. So, the data is transmitted to the Oizom cloud in near real-time. Additionally, it has an inbuilt memory backup to ensure no data loss in case of network failure. This ensures the best device uptime. The collected data can be visualized on the Oizom IoT Terminal in the form of real-time dashboards, upon collection on a dense network of data points and integrating weather data we can also generate odour plumes and odour dispersion heatmaps.
Weathercom
Weathercom is an Automatic Weather Station (AWS). It measures meteorological parameters such as wind speed & direction, rainfall, visibility, UV-radiation, light intensity, temperature, humidity, pressure, etc. Through Weathercom, monitoring of hyper-local meteorological parameters can be possible in real-time, which can help to make on-time decisions in case of any natural hazard. Weather forecasting and predictions are also possible through historical data and trend analysis, which can aid in timely warning/alert broadcasting. Easy installation of our automatic weather station along with our plug-and-play feature, and the solar panel makes it independent of any power source. It can withstand extreme weather conditions from tropical heat to arctic cold as well as extreme wind and rains. These features make Weathercom an ideal choice for comprehensive meteorological monitoring.
Tocadero EVO
Horiba Tocader's EVO series TOC Analyzers for Pharmaceuticals or both in process and portable versions monitor organic pollution through the determination of the TOC of pure and ultrapure water, a fundamental requirement for quality assurance in the highest value-added productions such as the semiconductor industry. Water from the power plant sector and in the chemical industry also increasingly requires online monitoring of this parameter at very low range. For immediate detection of out-of-specification TOCs in these critical productions, the most important requirement is a rapid response from analytical instrumentation: TOC analyzers based on UV oxidation and conductivity are ideal for this purpose. For example, water monitoring for cleaning and rinsing production plants (clean-in-place, CIP) is a classic application of TOC analyzers for pharmaceuticals. In the pharmaceutical sector, moreover, the different water qualities are also defined according to different pharmacopoeias such as the European Pharmacopoeia (EP) or USP for the United States: PW (purified water), HPW (higly purified water) and WFI (water for injection) are common concepts and differential conductivity analyzers have established themselves on the market as the way to continuously check this water in accordance with pharmaceutical requirements. In addition to the analytical background, particularly important aspects are measurement availability, reliability and ease of maintenance.
WaterSam WS316 Stationary Sampler
WS 316 Stationary Sampler Whether for indoor or outdoor use, the WS 316 is an all-rounder that impresses with its generous storage space and expandability. It can be tailored for a wide variety of different sampling requirements and conditions, and can even be retrofitted later with other equipment. The WS 316 even has room for extended bottle sets. - Housing and roof made of durable stainless steel - Three separate technical compartments in the upper section of the sampler to protect the pump, electronics and refrigeration unit - Freely adjustable and highly accurate temperature control for the sample storage chamber, for ambient temperatures from -25°C to +42°C – optionally from -40°C up to +55°C High-performance vacuum sampling system – alternatively available with any other WaterSam sampling system Borosilicate glass metering vessel protected in sample storage chamber to minimize sample falsication that could stem from temperature extremes Hose inlet on the left and right side; optionally from below Available with a composite container up to 60 l, or with an XY Distributor for direct filling of numerous bottle sets (up to 49 x 1 l or 64 x 350 ml) without cross-contamination - Wide range of optional equipment: housing materials, pumps, valves, equipment of challenging sample media and environments, sample freezing, etc.
WaterSam WS 312 Stationary Sampler
The WS 312 is a space-saving sampler for all standard indoor and outdoor applications. With its built-in cooling and heating, samples are stored reliably at the desired temperature. - Weather-proof housing and roof made of durable stainless steel; upper panel door included Three separate technical compartments in the upper section of the sampler to protect the pump, electronics and refrigeration unit - Freely adjustable and highly accurate temperature control for the sample storage chamber, for ambient temperatures from -25°C to +42°C - High-performance vacuum sampling system – alternatively available with any other WaterSam sampling system - Borosilicate glass metering vessel protected in sample storage chamber to minimize sample falsication that could stem from temperature extremes - Hose inlet on the left and right side; optionally from below - Available with XY Distributor for direct filling of numerous bottle sets without cross-contamination - Simple upgrade to monitoring station can be made at anytime - Wide range of optional equipment: housing materials, pumps, valves, etc.
WaterSam WS Porti Mobile Sampler
The WS Porti is a battery-operated sampler for remote locations, combining portability with renowned WaterSam quality. Thanks to the modular design, transportation is made easy and various sample bottle storage options can be used. - Built-in battery allows use away from mains power - Up to 3 week battery run time thanks to sleep mode and efficient technology _ Robust and durable stainless steel sampler housing - Standard-equipped with quality vacuum pump system and 12 mm suction line for reliable sampling of a variety of media - Optional compressor refrigeration with the ability to connect to vehicle socket for an uninterrupted cold chain during transport - Possibility of connection to various water quality sensors - An additional transport box enables quick replacement of full bottles
WaterSam WS Compact Mobile Sampler
The WS Compact is a battery-operated sampler. With its one-piece plastic housing and compact design, the sampler is easy to carry to remote locations. - Lightweight sampler housing made of HDPE - Built-in battery allows use away from mains power - Up to 3 weeks battery life with intelligent power saving mode - Socket for connecton of an external battery or charger - Socket for connecton of flow or event signal - USB-socket - Robust vacuum pump sampling system for highest repeatability, simple cleaning and minimal maintenance - Lockable with separate lock
INSTRAN ® online analyzers for chemical and physical parameters in aqueous solutions
INSTRAN ® is an online analyzer to measure different chemical and physical parameters in aqueous solutions, such as drinking water and waste water, which allows to control automatically the development of the parameter configured to make easier its control. INSTRAN ® is designed with the best and more resistant materials against aggressive chemical reagents as hydrochloric acid, caustic soda, etc. used to perform chemical reactions. Its optimal design, by experts with more than 30 years of experience on the field of online analysis and water quality, protects the critical mechanical spares, prolonging the shelf-life of them, and subsequently, the analyzer shelf-life too. It also implies that the analyzer maintenance is reduced. At the same time, the size and design of the reaction cell, reduces the consumption of reagents without it could affect the sensitive and accuracy of the measurement. All these features reduces the operational cost, which sometimes is extremely higher than the main analyzer price. Accuracy up to 0.015ml drop The exceptional and innovative dose system used by INSTRAN permits an accuracy up to 0.015ml drop, solving one of the critical parameters in online analysis and eliminating at all the several inconveniences created by the common peristaltic pumps. Unique versatility Instrumentación Analitica SA wrote and manages the analyzer software. It makes possible that the analyzer can be adapted to unusual sample conditions and difficult applications, according to customer needs. Thanks also to IA engineers high knowledge and suggestions, provides a unique versatility to the client. All these features makes INSTRAN ® provides a very accurate and reliable result, being the best available option in the market to control water quality.